Review

DeWalt DCG413B Review: Worth It? (November 2026)

Updated on · By the Best Angle Grinder Online team

The DeWalt DCG413B is worth buying if you already own 20V MAX batteries and want a cordless 4.5 in grinder with a kickback brake. Skip it if you need a corded grinder for heavy daily cutting.

DEWALT DCG413B 20V MAX Brushless Angle Grinder, the DeWalt DCG413B 20V MAX brushless angle grinder

In this review

DEWALT DCG413B 20V MAX Brushless Angle Grinder

Best for battery-owning DIYers9.1/10

See it on Amazon
On this page (8 sections)
  1. The DeWalt DCG413B at a glance
  2. Who should buy the DCG413B and who should skip it
  3. The specs that matter in daily use
  4. Setting up the DCG413B for the first cut
  5. Care and safe use over time
  6. The trade-offs to know before you buy
  7. Alternatives worth comparing
  8. Verdict: is the DeWalt DCG413B worth it?

The DeWalt DCG413B is worth buying if you already own 20V MAX batteries and want a cordless 4.5 in grinder for grinding, light cutting and cleanup work. It's the pick for battery-owning DIYers, and its kickback brake is the feature that sets it apart.

This DeWalt DCG413B review covers what the specs mean in daily use and where the tool falls short.

Skip it if you need sustained power for all-day metal work. A corded grinder gives you that without battery swaps.

Read on for the specs, setup, care and the alternatives worth comparing before you buy.

The DeWalt DCG413B at a glance

The DCG413B is a brushless 4.5 in cordless grinder built around the DeWalt 20V MAX battery platform. It brings a paddle switch, a two-stage trigger and a kickback brake to work where an extension cord won't reach.

1

DEWALT DCG413B 20V MAX Brushless Angle Grinder: Best for battery-owning DIYers

DEWALT DCG413B 20V MAX Brushless Angle Grinder, the DeWalt DCG413B 20V MAX brushless angle grinder
9.1/10Our score
  • Brushless motor
  • Kickback Brake
  • Paddle switch
  • 4-1/2 in wheel

A brushless 4.5 in cordless grinder with a kickback brake and paddle switch. It runs on DeWalt 20V MAX batteries you may already own.

See it on Amazon

Pros

  • Brushless motor needs no brush changes
  • Brake stops the wheel in 2 seconds or less on average
  • Kickback Brake shuts the grinder off during a bind-up
  • Two-stage trigger and E-Switch Protection

Cons

  • Battery and charger sold separately
  • 20 watts is modest for heavy stock removal
  • Corded grinders deliver more sustained power

The brake is the headline feature. DeWalt says it stops the wheel in 2 seconds or less on average, and the Kickback Brake cuts power when the tool senses a pinch or bind-up.

For a first cordless grinder, that's a safety feature worth paying attention to. The two-stage trigger backs it up by requiring two actions to start the tool.

Who this grinder is built for

It suits homeowners and trade users who already run 20V MAX tools. Sharing batteries across a drill, impact driver and grinder keeps the kit light and the cost down.

A single pack and charger then cover several tools, so the grinder arrives without its own charging kit to buy and store.

It also fits jobs away from an outlet: a gate hinge in the yard, a rusted bolt on a trailer or a fence bracket at the back of the property. The paddle switch is easy to find with a gloved hand when you're crouched over a cut.

If your work stays near a bench, a corded grinder is the simpler buy.

Who should buy the DCG413B and who should skip it

Buy the DCG413B if you own DeWalt 20V MAX batteries and want a safer cordless grinder for occasional cutting and grinding. The brake and the two-stage trigger are real advantages when you're working in awkward spots or around other people.

The tool-only format also means you aren't paying twice for batteries you already keep charged.

Skip it if your work is heavy or continuous. Long sessions cutting thick steel or grinding welds drain batteries and ask more of a 20 watt motor than a cordless tool comfortably gives.

A corded grinder runs as long as you do and never needs a pack swap in the middle of a cut.

Skip it too if this is your first angle grinder and you have no 20V MAX batteries. The tool-only kit means you'll add the cost of a battery and charger before you can make a single cut.

Factor that into the total and compare against a corded kit that arrives ready to run.

The specs that matter in daily use

The numbers that matter most are 3450 rpm, a 4.5 in wheel and 3.8 lb. Together they describe a grinder that's easy to control one-handed and quick to move between tasks.

The 4.5 in size is the common middle ground for cutting, grinding and flap-disc work, so discs are easy to find in shops and online.

DeWalt rates the motor at 20 volts and 20 watts. The horsepower figure is 0.16 hp.

Those are modest numbers, and they set the tool's place: light to medium work rather than heavy stock removal. The upside is that a smaller motor draws less from the pack, which helps runtime.

The brushless motor is the practical win. It needs no brush changes, and DeWalt says it offers a longer motor life.

For a tool you'll use in bursts over years, that's fewer maintenance jobs and one less part to wear out.

The brake and the Kickback Brake are the safety core. The brake slows the wheel when you release the trigger.

The Kickback Brake engages when the tool senses a pinch, stall or bind-up, stops the wheel with maximum force and shuts the grinder off. In a bind-up the wheel can kick the tool back toward the user, and cutting power fast reduces how far that movement goes.

E-Switch Protection adds a no-volt release. After a power cut or unexpected shutdown, you cycle the trigger off and on before the tool restarts.

That prevents a grinder springing back to life in your hands. The two-stage trigger needs two actions to start the tool, which reduces accidental startups.

The paddle switch is easy to reach with a gloved hand.

DeWalt covers the tool with a 3 year limited warranty. That's worth noting for a cordless tool whose main wear items, the motor and the electronics, are the parts you can't easily replace yourself.

Setting up the DCG413B for the first cut

Set up starts with a charged 20V MAX battery and the right 4.5 in wheel for the material. Fit the wheel, check the guard and confirm the disc's speed rating matches the grinder's 3450 rpm top speed.

A disc rated below that speed isn't safe on this tool, whatever the label says.

Check that the battery clicks fully into place. A loose pack can cut out mid-job, and the two-stage trigger won't help if the battery is only half seated.

Give the pack a firm push until it latches.

Hold the grinder in both hands before you start, with the wheel clear of the work. Let it reach full speed before touching the material.

The brake stops the wheel quickly after you release the trigger, so wait for it to stop before setting the tool down.

The E-Switch Protection means the trigger needs cycling after a shutdown. Get used to that on the first battery so it doesn't surprise you later.

If the tool won't start after a pause, cycle the switch before you assume a fault.

Keep the work area clear of people and flammable material. Sparks travel, so set up downwind and away from anything that can catch.

A dry powder extinguisher within reach is cheap insurance on any metal-cutting job.

Care and safe use over time

Care comes down to keeping the tool clean, the guard in place and the battery healthy. Wipe dust off the body and vents after each session, since metal dust and grit work their way into switches and bearings.

Blow out the vents rather than pushing dust deeper with a rag.

Check the guard and side handle before every use. A guard that's been removed for a tight cut should go back on as soon as the job is done.

The kickback brake reduces the risk from a bind-up, but it doesn't replace the guard. The brake is a backstop, not a licence to cut without protection.

Inspect wheels for cracks or chips and replace them when worn. Store the grinder where it won't get knocked, and keep spare discs flat and dry.

A warped or damp disc is a hazard, not a saving.

For the battery, follow DeWalt's charging guidance and store packs away from heat. A pack that's been dropped or gets hot during charging should come out of service.

Keep the contacts clean and free of metal dust, since a dirty terminal can cause a poor connection and a cut-out mid-job.

When the brake engages in a bind-up, stop and check the wheel and the work before restarting. A repeated bind-up usually means the disc is pinching, not that the tool is faulty.

Re-seat the work or change your approach before you try again.

The trade-offs to know before you buy

The main trade-off is power against portability. The 20 watt motor and 3450 rpm top speed handle light and medium jobs well.

They don't match a corded grinder for long cuts in thick steel or heavy weld grinding. If most of your work is heavy, the cordless convenience won't make up for the lower sustained output.

The tool-only kit is the second trade-off. DeWalt sells the DCG413B without a battery or charger, so the real cost is the tool plus a pack and charger unless you already own 20V MAX gear.

The brake and the brushless motor are what you're paying for, and the kit keeps that cost separate.

Weight sits at 3.8 lb without the battery. Add a pack and the grinder gets heavier in the hand, which matters for overhead work or long sessions.

The 12.2 x 4.7 x 6 in body is compact enough to store in a drawer or a small case, but the pack adds bulk as well as weight.

The 4.5 in wheel size limits you to discs in that size. That's the most common size for general work, so it's rarely a problem, but larger cutting jobs call for a bigger grinder.

The guard is shaped for that wheel size too, so you can't fit a larger disc without defeating the protection.

Battery runtime is the final consideration. A cordless grinder runs as long as the pack allows, and heavy cutting drains it faster.

Keep a spare charged pack if a job runs long. A spare pack costs money and takes space in the case, so plan for both.

Alternatives worth comparing

The DCG413B isn't the only DeWalt grinder worth a look. These alternatives suit different buyers, and each one fits a need the DCG413B doesn't cover as well.

Compare the wheel size, the power source and the safety features before you choose.

DeWalt DWE4011 for corded power at a low cost

The DWE4011 is the corded answer for buyers who want steady power without batteries. Our DeWalt DWE4011 angle grinder review covers its specs in full.

If your work stays near an outlet and you don't want to manage packs, a corded grinder is the simpler choice. It runs as long as you keep it plugged in and never asks you to swap a battery mid-cut.

The DCG413B wins on freedom of movement and on the kickback brake, so the right pick depends on where your work happens.

DeWalt DCG408B for a different 20V cordless option

The DCG408B is another 20V MAX grinder, and the DeWalt DCG408B 20V MAX angle grinder review compares it directly. It's worth a look if you want a second cordless option and already run DeWalt batteries.

Compare the two before you decide which one matches your work. Both share the same battery platform, so the choice comes down to the details of each tool rather than the packs.

Read both reviews side by side to see which fits your jobs.

A hard case for storage and transport

The Mchoi case fits the DCG413B and DCG416B and measures 13.5 x 6.1 x 6.4 in. Its EVA shell and soft lining protect the grinder from knocks, and the mesh pocket holds accessories.

The reinforced handle makes it easier to carry. It's sold as the empty case only, so the grinder and accessories aren't included.

It's a sensible add-on if the grinder lives in a truck or travels between jobs. The black and yellow color matches the DeWalt look, and the hard shell keeps the tool from getting squashed in a crowded toolbox.

Just confirm the fit for your exact model before you buy.

Verdict: is the DeWalt DCG413B worth it?

The DeWalt DCG413B is worth it for battery-owning DIYers who want a cordless 4.5 in grinder with real safety features. The brushless motor, brake and Kickback Brake make it a smart pick for light and medium work away from an outlet.

That's the core of this DeWalt DCG413B review.

Buy it if you already have 20V MAX batteries and want a safer cordless grinder. Pick a corded model instead if your work is heavy and continuous.

The kickback brake and the two-stage trigger are the details that justify the price for the right buyer. If you're weighing the DeWalt cordless line as a whole, our guide to the best DeWalt angle grinder puts the models side by side.

And if you're still deciding between two corded 4.5 in models, the DeWalt DWE402 vs DWE4011 comparison helps you choose between them.

Frequently asked questions

Does the DeWalt DCG413B come with a battery?

No. DeWalt sells the DCG413B as a tool-only kit, so the battery and charger are separate.

That makes it a good fit if you already have 20V MAX packs, but budget for a battery and charger if this is your first DeWalt tool.

What size wheel does the DCG413B take?

It takes a 4-1/2 inch wheel and spins at up to 3450 rpm. Match any disc you buy to that size and speed rating, and check the disc's own maximum rpm before mounting it on the grinder.

What does the kickback brake do on this grinder?

DeWalt says the Kickback Brake senses a pinch, stall or bind-up and applies the electronic brake with maximum force, then shuts the tool off. The separate brake also stops the wheel in 2 seconds or less on average when you release the trigger.

Is the DCG413B good for cutting metal?

It handles light to medium cutting on metal with the right wheel. The cordless 20V motor and 3450 rpm top speed suit occasional jobs, while long continuous cuts are easier on a corded grinder that never needs a battery swap.