How to Cut Metal With an Angle Grinder
To cut metal with an angle grinder, fit a thin metal cut-off wheel, clamp the workpiece so it can't move, and keep the guard between your hand and the wheel while you run the grinder along a marked line. Let the wheel's edge do the cutting at a steady speed rather than forcing it through the metal.
On this page (8 sections)
- What wheel do you need to cut metal?
- How do you mark and clamp metal before cutting?
- How do you hold and move the grinder through a cut?
- How do you cut a straight line, a pipe or a square hole?
- What safety gear and setup should you use?
- How do you avoid jams, kickback and cracked wheels?
- What should you do after the cut?
- How do you cut metal with an angle grinder safely?
To cut metal with an angle grinder, fit a thin metal cut-off wheel, clamp the workpiece so it can't move, and keep the guard between your hand and the wheel while you run the grinder along a marked line. Let the wheel's edge do the cutting at a steady speed rather than forcing it through the metal.
This is the core skill behind most metal work with an angle grinder, and it rewards patience more than force. A sharp wheel, a solid clamp and good eye protection matter more than how hard you push.
What wheel do you need to cut metal?
A thin abrasive cut-off wheel rated for ferrous metal is the right choice. It's designed for slicing through steel, not for grinding a surface flat.
A typical wheel for a 4-1/2 inch grinder measures about 0.045 inches thick with a 7/8 inch arbor.
Thin wheels cut fast with less heat and less material lost to the kerf. The trade-off is that they're more fragile than thick grinding discs, so they need a straight, steady hand and a guard.
Match the wheel's maximum RPM to your grinder's speed. A wheel rated lower than the tool's no-load speed can fail.
Also confirm the wheel's stated material type, since masonry and stone wheels are different animals and shouldn't be used on steel.
The DEWALT DW8062B5 pack is a good example of the type. These 4-1/2 inch wheels are aluminum oxide with two sheets of fiberglass for strength and a maximum speed of 13,300 RPM.

Thin fiberglass-backed wheels rated to 13,300 RPM for cutting steel, pipe and rebar.
See it on AmazonDEWALT rates them for carbon steel, stainless and nickel-based alloys. That range covers most jobs around a shop or garage.
The five-pack keeps a spare on hand when one wheel wears down.
Skip these if you're cutting concrete or tile; those jobs call for a different wheel type. Also skip a wheel that's chipped or has been dropped, even if it looks intact.
How do you mark and clamp metal before cutting?
Mark the cut line clearly and lock the metal down so it can't shift. Movement during a cut is the most common cause of a jammed or shattered wheel.
Use a scribe for precise lines on clean steel, or soapstone on rougher stock where a fine mark would be lost. A straight edge clamped to the work gives the wheel a guide to follow and keeps the cut square.
Clamp the workpiece to a bench, sawhorse or welding table so the cut is supported on both sides. A piece that sags as you cut pinches the wheel.
If you must cut near the end of a long piece, support the offcut too.
Keep the metal flat and steady. For pipe or tubing, a V-block or a clamp across the diameter stops rolling.
For angle iron, clamp the leg down so the wheel enters the corner cleanly.
How do you hold and move the grinder through a cut?
Grip the tool with both hands, start the wheel clear of the metal, and bring it down slowly. Let the wheel reach full speed before it touches the work.
Hold the body with one hand on the rear handle and the other on the side handle. The side handle gives you control and leverage, so fit it on the side that keeps your arm comfortable and away from the cut line.
Set the guard so the open side of the wheel faces away from you. The wheel should spin into the metal in the direction that throws sparks and debris toward the floor or a safe wall, not toward your body.
Lower the spinning wheel to the line and use light pressure. Let the abrasive edge do the cutting; pushing harder slows the wheel, builds heat and shortens its life.
Move steadily along the mark in one smooth pass for thin stock.
How much pressure should you use?
Use just enough pressure to keep the wheel cutting, which feels lighter than most people expect. If the wheel slows or the sparks change color to a dull orange, you're pushing too hard.
A sharp wheel makes bright, steady sparks and a clean kerf. Back off when the metal starts to blue or the cut wanders.
Overheating can harden the edge of a cut and make cleanup harder.
How do you cut a straight line, a pipe or a square hole?
Each shape needs a different guide, but the wheel technique stays the same. Straight lines follow a fence, pipe needs a clamp that stops rolling, and square holes start with drilled corners.
For a straight line, clamp a straight edge as a fence and rest the edge of the guard against it. Make a light scoring pass first, then follow the groove for the full depth.
This keeps the cut true over long pieces.
For pipe or tubing, wrap a strip of paper or a pipe wrap around the circumference to mark a square line. Clamp the pipe so it can't rotate, then cut around the mark in one steady rotation.
Rotate the pipe as you go rather than twisting the grinder around a fixed pipe.
For a square hole, drill the four corners first so the wheel has clearance. Cut each side between the holes, keeping the wheel square to the surface.
Finish the corners with a file, since the wheel leaves a small radius.
What safety gear and setup should you use?
Eye and face protection come first, then hearing and hand protection. A cut-off wheel throws sparks and fragments, and a broken wheel sends pieces fast.
A full face shield over safety glasses gives the best coverage. The NoCry face shield is ANSI Z87+ certified with an anti-fog and anti-scratch visor, and its ratchet knob adjusts the fit.

An ANSI Z87+ rated full face shield with an anti-fog visor that fits over glasses.
See it on AmazonIts curved visor is designed for all-around face coverage and is made up to 2x thicker for durability. The four-position angle adjustment lets you tip it to suit how you hold the grinder.
An extra set of sweatbands comes in the box.
Skip this shield if you only need light eye protection and already wear rated safety glasses with side shields. A face shield still pairs well with glasses, since neither replaces the other for grinding and cutting.
Add ear protection for long cuts and gloves for handling hot metal. Clear the area of flammable material and know where sparks will land.
A dry powder extinguisher nearby is sensible for shop work.
Why keep the guard on?
The guard deflects sparks and broken wheel pieces away from your body. It's not optional, and removing it to fit into a tight spot trades a small gain for a real risk.
A wheel can shatter if it binds or gets twisted. The guard catches the larger pieces and sends most debris away from your face.
Fit it so the closed section sits between you and the wheel.
How do you avoid jams, kickback and cracked wheels?
Keep the wheel straight in the cut and never twist it sideways. Sideways force is the main way thin wheels crack and bind.
A wheel that jams in the kerf can kick the grinder back toward you. Keep a firm two-handed grip and stand to the side of the wheel's path, not in line with it.
If the wheel binds, release the trigger and let it stop before pulling it out.
Don't cut with the flat of the wheel or use it to pry. Also avoid cutting stock that's under tension; it can pinch the wheel as it releases.
Support the offcut and cut toward the supported side.
Let the wheel spin down on its own after a cut. Don't stop it against the workpiece or the bench, which can damage the wheel or the guard.
What should you do after the cut?
Let the metal cool, then knock off the burr and check the wheel. The cut edge will be sharp and may have a thin burr along one side.
Cool the piece before handling it, since freshly cut steel stays hot for a while. Run a file or a grinding disc lightly along the edge to remove the burr, and wear gloves.
Check the cut-off wheel for chips or cracks before storing it. A wheel that's been dropped or run hot should be replaced rather than reused.
Store spare wheels flat and dry.
Sweep up the metal dust and sparks when the work is done. Clean dust out of the grinder's vents so it doesn't pull grit into the motor over time.
Which grinder suits regular metal cutting?
The Makita 9557PB is a compact 4-1/2 inch grinder with a 7.5 amp motor that delivers a no-load speed of 11,000 RPM. Its small 2-1/2 inch barrel and 4.5 lb weight make it easier to control for long cuts.

A compact 4-1/2 inch grinder with a 7.5 amp motor and 11,000 RPM for steady metal cuts.
See it on AmazonIt has a paddle switch with a lock-on feature for continuous operation and an AC/DC switch for use with an alternative power source. The labyrinth construction is designed to seal and protect the drive gear and bearings from contamination.
It ships with a grinding wheel, wrench, side handle, flange and wheel guard.
Skip it if you need a larger wheel for deep cuts in heavy stock. Check the angle grinder sizes comparison to see how a 4-1/2 inch model compares with 5 and 6 inch tools before you buy.
How do you cut metal with an angle grinder safely?
The safe routine is simple: fit a metal cut-off wheel, fit the guard and face shield, clamp the work, and cut with light steady pressure. Then let the metal cool and clear the burr.
For most readers, the DEWALT wheel pack covers the cutting, the NoCry shield covers the face, and a compact 4-1/2 inch grinder like the Makita 9557PB handles the motor side. A larger grinder suits heavier stock, and the sizes guide helps you decide.
If your next job involves masonry, see how to cut bricks with angle grinder for the wheel and technique changes. And if you're wondering about softer stock, can angle grinders cut wood explains why that's a different and more dangerous job.
Frequently asked questions
Can you cut metal with a grinding wheel instead of a cut-off wheel?
No. A grinding wheel is thick and meant for surface work, so it cuts slowly, heats the metal and loads up in a narrow kerf.
Use a thin cut-off wheel rated for metal and the grinder's RPM.
What speed should an angle grinder run at for cutting metal?
Run the grinder at its rated no-load speed and let the wheel's rating match or exceed it. Thin wheels cut best at full speed with light, steady pressure, and slowing down by forcing the cut causes heat and wheel wear.
Do you need a diamond blade to cut metal?
No. Diamond blades are for masonry, tile and stone.
Ferrous metal cutting uses abrasive wheels made from aluminum oxide or similar grains, and diamond can clog and overheat on steel.
How do you cut a straight line with an angle grinder?
Mark the line with a scribe or soapstone, clamp a straight edge as a fence, and rest the edge of the guard or wheel against it. Take light passes along the fence instead of trying to cut the full depth in one push.
Can you cut metal with an angle grinder without a guard?
No. Keep the guard fitted and positioned so it covers the wheel between your body and the cut.
A guard cannot stop every fragment, but it deflects most sparks and broken wheel pieces away from your face and hands.
How do you cut a square hole in metal with an angle grinder?
Drill the corners first so the wheel has room to turn, then cut each side between the holes with a thin cut-off wheel. Clamp the plate flat, keep the wheel square to the surface, and finish the corners with a file.
About this guide: Our look at cutting metal with an angle grinder draws on maker specs, materials and what owners report. See how we research.



